Sapa Lift-and-Slide Door 2160S XS

Lift-and-Slide Door 2160S XS is made of insulated aluminum profiles with a frame depth of 160 mm and a door leaf  depth of 70 mm. The insulation consists of 50 mm wide glass fibre reinforced polyamide strips. The lift-and-slide door has lift-slide fittings for user-friendly handling. The door leaf is easily slid aside and seals all around as the door leaf is lowered a few millimeters in closed position. 

Sapa 2160S XS offers a bigger glass surface and transparency through reducing sightline to 36 mm compared with 92 mm for 2160S

Sapa 2160S XS is produced by Hydro CIRCAL - Recycled and low carbon aluminium. Read more about it here.

Lift-and-Slide Door 2160S XS Performance

    • Door leaf dimensions. Max recommended width 2,8 m (up to 3,1 m possible in wind sheltered areas). Max recommended height 2,6 m (up to 2,8 m possible in wind sheltered areas). Recommendations are done considering normal wind load.
    • Door leaf weight. Max 330 kg
    • Glass rebate. 23-50 mm
    • Lockable fittings. Inside or in- and outside.
    • Air tightness. Class 4 according to EN 12207 (600 Pa)
    • Water resistance. 9A enligt EN 12208 (600 Pa)
    • Wind load resistance. Class C3 according to EN12210 (1200 Pa)
    • Versions: Monorail or duo-rail lift-sliding door with the following possible combinations:
      - Monorail: Single-sliding door leaf
      - Duo-Rail: Single-sliding door leaf, two sliding door leaves.

Elevations & Details

A2160-1017 1234567
Save this elevation as: dwg / dxf
Click on number to view the details
A2160-1018 1234567
Save this elevation as: dwg / dxf
Click on number to view the details
A2160-1019 1234567
Save this elevation as: dwg / dxf
Click on number to view the details

Drawing texts

The texts are intended to help the specificators to specify which systems, fittings, glazing units, surface treatment alternatives and functions are required. They are later used by the licensed fabricators during the production of the finished products.

Download the text as .dwg
Download the text as .pdf

Fitting functions

Lift sliding door 2160S XS can be performed as one fixed and one sliding door leaf, alternatively with two sliding door leaf.

For opening the handle is turned 180° downwards, whereby the door is lifted a few millimeters and can easily be slid aside. When closing the door leaf goes down again and the rubber sealing tightens all around. The door leafs run silently on nylon rollers on a stainless rail and can be parked (lowered) at any position.

Each sliding door leaf is equipped with  espagnolette with four anchor points. Handles of aluminium and cylinder locks can be mounted on the inside and outside or inside only.

Handle

Lift handle, inside Lift handle, inside
Pull handle, outside
Lift handle  for cylinder lock, inside Lift handle for cylinder lock,
inside and outside
 
Lift handle for cylinder lock, inside
Oull handle, outside
 

Wheels

Location in the wall

For the entire structure to meet the energy saving requirements and ensure good comfort it is necessary to install the sliding terrace door in the warm part of the wall. This means that it should be installed as deep into the wall as possible, which has a number of advantages.

It creates good conditions for appropriate fixing and a well functioning joint. The risk of condensation is reduced due to a higher surface temperature. The joint between the frame profile and the wall shall be made with two step sealing. This means that it should consist of an outer rain barrier with an underlying air channel, a mineral wool insulation layer and an inner diffusion sealing joint.

Glazing

Unprotected glazed surfaces which are so located that they can be reached by persons shall be designed so as to limit the risk of injury. Such glazed surfaces shall be dimensioned so as to withstand the dynamic influence of a person. Applicable standards and requirements should be taken into account.


Glass thickness 23-50 mm


The illustration shows the different functional dimensions commonly used by the window industry and established by the MTK. The gaskets are made of EPDM rubber and are available in several versions.

U values for lift-sliding door

Formula for calculating the total U value of a sliding door, taking into account the glazing unit, the share of profiles and an edge zone effect linear factor.

Usliding door = Ag * Ug + Af * Uf + Ig * ψg )  /  ( Ag + Af )

The calculations are based on the requirements and general guidelines.

Lift-sliding door U value of glass Ug W/m2K (middle point) 

Warm edge distance strip
width x height mm 0,6 0,9 1,1
3000 x 2300 1,3 1,5 1,7
4000 x 2300 1,2 1,4 1,6
5000 x 2300 1,1 1,4 1,6

Fixing principles

Lift-sliding doors must be fixed to a stable and suitable wall structure. The choice of fixing method depends on the wall type. The number and location of fixing points depends on the size of the door.

Example:

Fixing of frame with twist anchor inwards Fixing of frame with twist anchor outwards

 

Product overview

Lift-and-Slide Door 2160S XS is made of insulated aluminum profiles with a frame depth of 160 mm and a door leaf  depth of 70 mm. The insulation consists of 50 mm wide glass fibre reinforced polyamide strips. The lift-and-slide door has lift-slide fittings for user-friendly handling. The door leaf is easily slid aside and seals all around as the door leaf is lowered a few millimeters in closed position. 

Sapa 2160S XS offers a bigger glass surface and transparency through reducing sightline to 36 mm compared with 92 mm for 2160S

SAPA BUILDING SYSTEMS -
Please choose your language